bootlog-tilgin_HG2384_BBCBE0_hongkong_hkbn.txt

ROM VER: 1.0.0
CFG 06
NAND

ROM VER: 1.0.0
CFG 06
NAND

DDR autotuning Rev 1.0
DDR size from 0xa0000000 - 0xa3ffffff
DDR check ok... start booting...



Tilgin UBI HG228x/238x U-Boot 2010.06-LANTIQ-v-2.3.115 (Feb 21 2017 - 09:48:29) 02_10_00_87

CLOCK CPU 720M RAM 360M
16 Bit RAM
DRAM:  128 MiB
NAND:  ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0xef, Chip ID: 0xf1 (WINBOND W29N01HV)
128 MiB
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000000080000 : "U-Boot"
Creating 1 MTD partitions on "nand0":
0x000000080000-0x000008000000 : "ubi"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: max. sequence number:       3351
UBI: attached mtd2 to ubi0
UBI: MTD device name:            "ubi"
UBI: MTD device size:            127 MiB
UBI: number of good PEBs:        1019
UBI: number of bad PEBs:         1
UBI: number of corrupted PEBs:   0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    256
UBI: number of internal volumes: 1
UBI: number of user volumes:     14
UBI: available PEBs:             287
UBI: total number of reserved PEBs: 732
UBI: number of PEBs reserved for bad PEB handling: 10
UBI: max/mean erase counter: 10/3
UBI: image sequence number:  219832608
Volume Environment (ID 14) found at slot 14
Read 7936 bytes from volume 14 to 86c332a8(buf address)
In:    serial
Out:   serial
Err:   serial
Board reset caused by unknown (3c08a060).

Net:   internal phy using 25Mhz clock
Firmware is VR9 V1.2 GPHY GE
Internal phy firmware version: 0x8435
PHY version 8435
ar10 Switch

Type "run flash_flash" to start the Linux kernel

Hit any key to stop autoboot:  1  0 

No private boot packet is detected
Volume kernel (ID 6) found at slot 6
Read 0 bytes from volume 6 to 80500000(buf address)
Read [2064384] bytes
## Booting kernel from Legacy Image at 80500000 ...
   Image Name:   Linux-3.10.104
   Created:      2021-11-05  16:53:16 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1959693 Bytes = 1.9 MiB
   Load Address: 80002000
   Entry Point:  8000a970
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Initializing cgroup subsys cpu

Linux version 3.10.104 (helen@ac64226107ac) (gcc version 4.8.3 20140401 (prerelease) (Linaro GCC 4.8-2014.04) ) #2 Fri Nov 5 16:53:00 UTC 2021

SoC: xRX330 rev 1.1

bootconsole [early0] enabled

CPU0 revision is: 00019556 (MIPS 34Kc)

Product ID: HG2384 model HG228x/238x - Tilgin Home Gateway HG228x/238x

adding memory size:119537664 from DT

MIPS: machine is HG228x/238x - Tilgin Home Gateway HG228x/238x

Determined physical RAM map:

 memory: 07200000 @ 00000000 (usable)

reserving 32768 bytes @ 71f8000 for printk backup buffer

Zone ranges:

  Normal   [mem 0x00000000-0x071fffff]

Movable zone start for each node

Early memory node ranges

  node   0: [mem 0x00000000-0x071fffff]

Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.

Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 28956

Kernel command line: mtdparts=ifx_nand:0x80000@0x0(U-Boot),-@0x80000(ubi) ubi.mtd=ubi root=mtd:rootfs ip=192.168.1.1:192.168.1.3::::eth0:on console=ttyS0,115200 ethaddr=14:AE:DB:BB:CB:E0 ID_SerialNumber=C4810052626 ID_ProductID=HG2384 ID_MAC_0=14:AE:DB:BB:CB:E0 ID_MAC_1=14:AE:DB:BB:CB:E1 ID_MAC_2=14:AE:DB:BB:CB:E2 ID_MAC_3=14:AE:DB:BB:CB:E3 ID_MAC_4=14:AE:DB:BB:CB:E4 ID_MAC_5=14:AE:DB:BB:CB:E5 ID_MAC_6=14:AE:DB:BB:CB:E6 ID_MAC_7=14:AE:DB:BB:CB:E7 panic=1 loglevel=7 UBOOT_VERSION="02_10_00_87" UBOOT_DATETIME="Feb 21 2017 - 09:48:40" RESET_CAUSE=unknown boot_cond=0 vpe1_load_addr=0x87f00000 vpe1_mem=1M wlanm=126

PID hash table entries: 512 (order: -1, 2048 bytes)

Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

Writing ErrCtl register=00027af0

Readback ErrCtl register=00027af0

Memory: 109340k/116736k available (4192k kernel code, 7396k reserved, 1401k data, 412k init, 0k highmem)

NR_IRQS:256

Setting up vectored interrupts

CPU Clock: 720MHz

Calibrating delay loop... 479.23 BogoMIPS (lpj=2396160)

pid_max: default: 32768 minimum: 301

Security Framework initialized

Mount-cache hash table entries: 512

Initializing cgroup subsys devices

Initializing cgroup subsys freezer

Initializing cgroup subsys blkio

pinctrl core: initialized pinctrl subsystem

NET: Registered protocol family 16

dma-xway 1e104100.dma: Init done - hw rev: 8, ports: 5, channels: 24

pinctrl-xway 1e100b10.pinmux: invalid group "exin3" for function "exin"

pinctrl-xway 1e100b10.pinmux: Init done

Init done

gpio-stp-xway 1e100bb0.stp: Init done

!!!!!!! WAVE400 system registeration on AHB 

MTLK_MEM_BAR1_START is 1a000000

MTLK_MEM_BAR1_END is 1a7fffff

MTLK_WIRELESS_IRQ_IN_INDEX is 26

PCI host bridge /fpi@10000000/pcie@d900000 ranges:

 MEM 0x000000001c000000..0x000000001cffffff

  IO 0x000000001d800000..0x000000001d8fffff

pcie_wait_phy_link_up port 0 timeout

pcie_wait_phy_link_up port 0 timeout

pcie_wait_phy_link_up port 0 timeout

pcie_wait_phy_link_up port 0 timeout

pcie_wait_phy_link_up port 0 timeout

pcie_rc_initialize port 0 link up failed!!!!!

ltq-pcie: probe of 1d900000.pcie failed with error -5

PCI host bridge /fpi@10000000/pcie@9B00000 ranges:

 MEM 0x000000001b000000..0x000000001bffffff

  IO 0x0000000019a00000..0x0000000019afffff

Lantiq PCIe Root Complex Port 2 Init Done

bio: create slab <bio-0> at 0

SCSI subsystem initialized

Register xway nand done!

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

PCI host bridge to bus 0000:00

pci_bus 0000:00: root bus resource [mem 0x1b000000-0x1bffffff]

pci_bus 0000:00: root bus resource [io  0x19a00000-0x19afffff]

pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]

ltq-pcie 19b00000.pcie: pcie_rc_class_fixup port 2: fixed pci host bridge to pci-pci bridge

pci 0000:00:00.0: BAR 8: assigned [mem 0x1b000000-0x1b1fffff]

pci 0000:00:00.0: BAR 9: assigned [mem 0x1b200000-0x1b2fffff pref]

pci 0000:01:00.0: BAR 0: assigned [mem 0x1b000000-0x1b1fffff 64bit]

pci 0000:01:00.0: BAR 6: assigned [mem 0x1b200000-0x1b20ffff pref]

pci 0000:00:00.0: PCI bridge to [bus 01]

pci 0000:00:00.0:   bridge window [mem 0x1b000000-0x1b1fffff]

pci 0000:00:00.0:   bridge window [mem 0x1b200000-0x1b2fffff pref]

PCI: Enabling device 0000:00:00.0 (0000 -> 0002)

NET: Registered protocol family 8

NET: Registered protocol family 20

Switching to clocksource MIPS

NET: Registered protocol family 2

TCP established hash table entries: 1024 (order: 1, 8192 bytes)

TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

TCP: Hash tables configured (established 1024 bind 1024)

TCP: reno registered

UDP hash table entries: 256 (order: 0, 4096 bytes)

UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

NET: Registered protocol family 1

ltq-pcie 19b00000.pcie: pcie_fixup_bridge port 2 : fixup host controller 0000:00:00.0 (1bef:0011)

gptu: totally 6 16-bit timers/counters

gptu: misc_register on minor 63

gptu: succeeded to request irq 126

gptu: succeeded to request irq 127

gptu: succeeded to request irq 128

gptu: succeeded to request irq 129

gptu: succeeded to request irq 130

gptu: succeeded to request irq 131

vpe1_mem = 100000

Wired TLB entries for Linux read_c0_wired() = 0

squashfs: version 4.0 (2009/01/31) Phillip Lougher

msgmni has been set to 213

io scheduler noop registered

io scheduler deadline registered (default)

gpio-export gpio-export.8: 1 gpio(s) exported

lantiq,asc 1e100c00.serial: pins are not configured from the driver

1e100c00.serial: ttyS0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc

console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled

Tilgin initialization is OK
tilgin-hg-ltq-gphy tilgin-hg-ltq-gphy.9: Lantiq GPHY kthread created
tilgin-hg-ltq-gphy tilgin-hg-ltq-gphy.9: gpio_base=166
loop: module loaded
slram: not enough parameters.
ONFI param page 0 valid
ONFI flash detected
NAND device: Manufacturer ID: 0xef, Chip ID: 0xf1 (WINBOND W29N01HV), 128MiB, page size: 2048, OOB size: 64
Scanning device for bad blocks
Bad eraseblock 768 at 0x000006000000
2 ofpart partitions found on MTD device 14000000.nand-parts
Creating 2 MTD partitions on "14000000.nand-parts":
0x000000000000-0x000000080000 : "U-Boot"
0x000000080000-0x000008000000 : "ubi"
USIF: ifx_get_usif_hz returned: 100000000 and rmc: 1
USIF: spi_clock : 100000000
USIF: setting baud rate to: 2000000
Lantiq USIF-SPI driver, version 1.3.2, (c) 2001-2013 Lantiq Deutschland GmbH
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Lantiq VRX318 Version 3.0.0 
LTQ ETH SWITCH API, Version 2.0.1.
SWAPI: Registered char device [switch_api] with major no [81]
Switch API: PCE MicroCode loaded !!
phy_port_nos[0]:0, phy_fw_type[0]:0
phy_port_nos[1]:0, phy_fw_type[1]:0
phy_port_nos[2]:0, phy_fw_type[2]:0
phy_port_nos[3]:0, phy_fw_type[3]:0
gphy_driver_init: fw_mode:11G-FW, no of phys:4, mode:0
PPP generic driver version 2.4.2
NET: Registered protocol family 24
res = 86d52a80
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usb-storage
input: gpio-keys-polled.6 as /devices/gpio-keys-polled.6/input/input0
wdt 1f8803f0.watchdog: Init done
leds-gpio gpio-leds.5: pins are not configured from the driver
attach gpio 183 (name 3:green) ret 0
attach gpio 184 (name 3:red) ret 0
attach gpio 180 (name 4:green) ret 0
attach gpio 181 (name 4:red) ret 0
attach gpio 192 (name 5:green) ret 0
attach gpio 179 (name 5:red) ret 0
attach gpio 220 (name 6:green) ret 0
attach gpio 187 (name 7:green) ret 0
attach gpio 188 (name 7:red) ret 0
attach gpio 193 (name 8:green) ret 0
attach gpio 186 (name 8:red) ret 0
attach gpio 185 (name 1:red) ret 0
attach gpio 191 (name 6:red) ret 0
Lantiq DEU driver version 2.0.0 
LTQ DEU DES initialized.
LTQ DEU AES initialized.
LTQ DEU ARC4 initialized
LTQ DEU SHA1 initialized
LTQ DEU MD5 initialized 
LTQ DEU SHA1_HMAC initialized
LTQ DEU MD5_HMAC initialized
DEU driver initialization complete!
u32 classifier
    Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1708 buckets, 6832 max)
ctnetlink v0.93: registering with nfnetlink.
nf_ct_ipsec_ike: registering helper for pf: 2 port: 500
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP: cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
KOAM is loaded successfully.
l2tp_core: L2TP core driver, V2.0
l2tp_ppp: PPPoL2TP kernel driver, V2.0
8021q: 802.1Q VLAN Support v1.8
UBI: crypto extension enabled
UBI: attaching mtd1 to ubi0
UBI: scanning is finished
UBI: attached mtd1 (name "ubi", size 127 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
UBI: VID header offset: 512 (aligned 512), data offset: 2048
UBI: good PEBs: 1019, bad PEBs: 1, corrupted PEBs: 0
UBI: user volume: 14, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 10/3, WL threshold: 256, image sequence number: 219832608
UBI: available PEBs: 278, total reserved PEBs: 741, PEBs reserved for bad PEB handling: 19
UBI: background thread "ubi_bgt0d" started, PID 353
Map root mtd:rootfs to device /dev/mtdblock8
VFS: Mounted root (squashfs filesystem) readonly on device 31:8.
Freeing unused kernel memory: 412K (80579000 - 805e0000)

starting pid 411, tty '': '/etc/init.d/rcS'
UBIFS: background thread "ubifs_bgt0_1" started, PID 431
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 1, name "package"
UBIFS: LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 30191616 bytes (28 MiB, 234 LEBs), journal size 1548288 bytes (1 MiB, 12 LEBs)
UBIFS: reserved for root: 1426023 bytes (1392 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID 68CFAAEE-84DC-4E49-AEB8-87ABE10D18C8, small LPT model
mount: mounting procbususb on /proc/bus/usb failed: No such file or directory
crm-cleanup: running...
tilgin-hg-ltq-gphy tilgin-hg-ltq-gphy.9: switch port #1 PHY ID is 0x1
tilgin-hg-ltq-gphy tilgin-hg-ltq-gphy.9: switch port #2 PHY ID is 0x2
tilgin-hg-ltq-gphy tilgin-hg-ltq-gphy.9: switch port #3 PHY ID is 0x3
tilgin-hg-ltq-gphy tilgin-hg-ltq-gphy.9: switch port #4 PHY ID is 0x4
tilgin-hg-ltq-gphy tilgin-hg-ltq-gphy.9: switch port #5 PHY ID is 0x5
Firmware version for port 1 is 435 - may be it's timeto enable power saving?
Firmware version for port 2 is 435 - may be it's timeto enable power saving?
Firmware version for port 3 is 435 - may be it's timeto enable power saving?
Firmware version for port 4 is 435 - may be it's timeto enable power saving?
Firmware version for port 5 is 435 - may be it's timeto enable power saving?
grep: /proc/753/cmdline: No such file or directory
grep: /proc/770/cmdline: No such file or directory
All modules unloaded
/tmp
crm-cleanup: done
udevd[859]: starting version 174
watchdog: keep enlantiq_wdt: WDT device closed but not stopped!
abled
pmem-read.squashfs: Restoring /var/log from Log (/dev/mtd/2)
pmem-read.squashfs: Restoring /var/etc from Config-A (/dev/mtd/5)
pmem-postread.config: Restoring /tmp/pmem2.JkxfI0 from Config-C (/dev/mtd/14)
pmem-read.squashfs: Restoring /var/miscA from Misc-A (/dev/mtd/11)
pmem-read.squashfs: Restoring /var/log from Log (/dev/mtd/2)
Jan  1 00:00:14 C Dispatcher: Init module logger	OK

RootFS version ESx003-02_07_05_14


BusyBox v1.21.1 (2016-12-01 22:27:29 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.

Retrieved safe mode threat limit 5
# Trying to start watchdog with timeout 10 seconds
umount: can't umount /usr/share/webui: Invalid argument
IFXUSB: ifxusb_hcd: version 3.2 B140220-tilgin271015
IFXUSB:    OPTION: __IS_AR10__
IFXUSB:    OPTION: __UEIP__
IFXUSB:    OPTION: __PHY_LONG_PREEMP__
IFXUSB:    OPTION: __UNALIGNED_BUF_ADJ__
IFXUSB:    OPTION: __ENABLE_DUMP__
IFXUSB:    OPTION: __NEW_COC__
IFXUSB:    OPTION: __IS_HOST__
IFXUSB:            __IS_DUAL__
IFXUSB:            __DYN_SOF_INTR__
IFXUSB:            __UEIP__
IFXUSB:            __DO_OC_INT__
IFXUSB:            __INTRNAKRETRY__
IFXUSB:            __INTRINCRETRY__
IFXUSB: USB core #0 soft-reset
IFXUSB: USB core #0 soft-reset
ifxusb_hcd ifxusb_hcd: IFX USB Controller
ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
ifxusb_hcd ifxusb_hcd: irq 54, io mem 0xbe101000
IFXUSB: Init: Power Port (0)
on/off switch 'usb1_power' not found
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
IFXUSB: USB core #1 soft-reset
IFXUSB: USB core #1 soft-reset
ifxusb_hcd ifxusb_hcd: IFX USB Controller
ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2
ifxusb_hcd ifxusb_hcd: irq 83, io mem 0xbe106000
IFXUSB: Init: Power Port (0)
on/off switch 'usb2_power' not found
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
cryptodev: module license 'BSD' taints kernel.
Disabling lock debugging due to kernel taint
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
usbcore: registered new interface driver usblp
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver rndis_host
usbcore: registered new interface driver cdc_ncm
[4294692186] mtlk0(mtlk_cdev_init:355): Max nodex set to 1048575
[4294693296] mtlk0(__mtlk_print_endianess:4915): The system is Big endian (0xbeadfeed, 0xedfeadbe)
[4294693296] mtlk<3>(_ahb_irq_get:429): Found device IRQ: 18
[4294693306] mtlk0(_mtlk_df_user_alloc_devname:8455): NDEV Name pattern: wlan%d
[4294693316] mtlk0(mtlk_core_pdb_fast_handles_open:44): Open Hot-path parameters
[4294693316] mtlk<4>(_mtlk_mmb_cleanup_reset_mac:3245): FW CPU reset is done
[MTLKD] BBCPU Reg: offs=0x01c0 (ba2f01c0) val=0xfff007e0 (offset_mb=126)
[MTLKD] Enabling interrupt (bf880208)
[MTLKD] Interrupt enabled
[MTLKD] ChipID: 0x07D0
[MTLKD] e-fuse: num 1, address 0xbf1073b0, word: 0x00000000, value: 0x000
[MTLKD] e-fuse: num 2, address 0xbf1073b4, word: 0x00000000, value: 0x000
[MTLKD] e-fuse: num 3, address 0xbf1073b8, word: 0x00000000, value: 0x000
[MTLKD] e-fuse: num 4, address 0xbf1073bc, word: 0x00000000, value: 0x000
[MTLKD] e-fuse: num 5, address 0xbf1073c0, word: 0x00000000, value: 0x000
[MTLKD] e-fuse: num 6, address 0xbf1073c4, word: 0x00000000, value: 0x000
mtlk mtlk.0: firmware: requesting cal_wlan0.bin
[4294693506] mtlk0(mtlk_mmb_drv_get_cpu_freq:604): FPI bus frequency: 360 MHz
mtlk mtlk.0: firmware: requesting ap_upper_ar10.bin
[4294693736] mtlk0(get_firmware_version:1161): CID-0000: ap_upper_ar10.bin: @@@ VERSION INFO @@@ version number: 3.4.2.40.05_NoPsTxCancel_2_r4540 MIPS:  Single CPU(TMC AGG AP) interface: PCI  phy type: real phy on Dec 31 2014 at 14:19:47@@@ END @@@

[4294693816] mtlk<4>(_mtlk_mmb_send_hw_dep_cfg:2443): AFE value: 0x23056012
[4294693846] mtlk0(mtlk_eeprom_check_ee_data:1353): Options mask is 0x00
[4294693846] mtlk0(load_default_hw_table:2119): HW configuration is 2X2
[4294694046] mtlk0(_mtlk_core_mbss_add_vap:7757): CID-0000: Got PRM_ID_VAP_ADD
[4294694056] mtlk0(_mtlk_df_user_alloc_devname:8455): NDEV Name pattern: wlan0.0
[4294694066] mtlk0(mtlk_core_pdb_fast_handles_open:44): Open Hot-path parameters
[4294694086] mtlk0(_mtlk_core_mbss_add_vap:7775): CID-0000: VAP#1 added
[4294694126] mtlk0(_mtlk_core_mbss_add_vap:7757): CID-0000: Got PRM_ID_VAP_ADD
[4294694126] mtlk0(_mtlk_df_user_alloc_devname:8455): NDEV Name pattern: wlan0.1
[4294694136] mtlk0(mtlk_core_pdb_fast_handles_open:44): Open Hot-path parameters
[4294694176] mtlk0(_mtlk_core_mbss_add_vap:7775): CID-0000: VAP#2 added
[4294694226] mtlk0(_mtlk_core_mbss_add_vap:7757): CID-0000: Got PRM_ID_VAP_ADD
[4294694226] mtlk0(_mtlk_df_user_alloc_devname:8455): NDEV Name pattern: wlan0.2
[4294694236] mtlk0(mtlk_core_pdb_fast_handles_open:44): Open Hot-path parameters
[4294694286] mtlk0(_mtlk_core_mbss_add_vap:7775): CID-0000: VAP#3 added
Loading D5 (MII0/1) driver ...... 
CHIPID: 1, chipid address: 0xbf107344
Succeeded!
PPE datapath driver info:
  Version ID: 128.3.3.1.2.14.1
  Family    : AR10
  DR Type   : Normal Data Path | Indirect-Fast Path
  Interface : MII0 | MII1
  Mode      : Routing
  Release   : 2.14.1
PPE firmware info:
  Version ID: 10.5.2.14.3
  Family    : GRX390
  FW Package: D5
  Release   : 2.14.3
PPE firmware feature:
  Packet Acceleration             Support
  IPv4                            Support
  IPv6                            Support
  6RD                             Support
  DS-Lite                         Support
PPA API --- init successfully
ifx_ppa_init - init succeeded
ifx_ppa_init - init succeeded
IFXOS, Version 1.5.16 (c) Copyright 2009, Lantiq Deutschland GmbH
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_pci: 10.2.85 (Atheros/multi-bss)
ath_pci_probe
PCI device id is 003c :003c
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
ath_pci 0000:01:00.0: ath DEBUG: sc=0x855d7200

 ol_ath_pci_configure : num_desired MSI set to 0

 Using PCI Legacy Interrupt
__ol_ath_attach: ath_attach TODO
__ol_ath_attach: dev name wifi0
ol_ath_attach() BMI inited.
ol_ath_attach() BMI Get Target Info.
ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c
NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
ol_ath_attach() configure Target .
Reading Flash for Calibraton data from 0x5000 and partition name is caldata
TILGIN ol_transfer_bin_file OS_NAND_FLASH_READ at 20480 (2116) OK
qc98xx_verify_checksum: flash checksum passed: 0xe0f3
ol_transfer_bin_file 1804: Download Flash data len 2116
ol_transfer_bin_file 1748: Download Firmware data len 218164
ol_ath_attach() Download FW. 
ol_ath_attach() HT Create .
ol_ath_attach() HIF Claim.
ol_ath_attach() BMI Done. 
ol_ath_attach() WMI attached. wmi_handle 85750000 
+HWT
CE_recv_buf_enqueue 625 Populate last entry 512 for CE 5
CE_recv_buf_enqueue 634 CE 5 wi 511 dest_ptr 0x46d8840 nbytes 0 recv_ctxt 0x846d68c0
-HWT
HTC Service:0x0300 ep:1 TX flow control disabled
CE_pkt_dl_len_set CE 4 Pkt download length 64
HTC Service:0x0100 ep:2 TX flow control disabled
wmi_service_ready_event_rx:  WMI UNIFIED SERVICE READY event 
num_rf_chain : 00000003
ht_cap_info: : 0000085b
vht_cap_info : 338001b2
vht_supp_mcs : 0000ffea
LARGE_AP enabled. num_peers 144, num_vdevs 16, num_tids 256
idx 0 req 1  num_units 0 num_unit_info 2 unit size 408 actual units 145 
chunk 0 len 59160 requested ,ptr  0x56e0000 
FIRMWARE:P 145 V 16 T 443
 
FIRMWARE:_wlan_rtt_enable 
wmi_ready_event_rx:  WMI UNIFIED READY event 
ol_ath_connect_htc() WMI is ready
ol_ath_set_host_app_area TODO
target uses HTT version 2.1; host uses 2.1
ol_ath_attach() connect HTC. 
ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
Add VHT80 channel: 5210
Add VHT80 channel: 5290
Add VHT80 channel: 5530
Add VHT80 channel: 5610
Add VHT80 channel: 5690
Add VHT80 channel: 5775
Skipping VHT80 channel 5825
ol_ath_phyerr_attach: called
OL Resmgr Init-ed
ol_if_dfs_setup: called 
ol_if_dfs_attach: called; ptr=84701974, radar_info=855cdc08
ol_ath_rtt_meas_report_attach: called
ol_ath_attach() UMAC attach . 
ol_if_dfs_configure: called
ol_if_dfs_configure: FCC domain
ol_if_dfs_disable: called
ol_ath_attach: Calling ol_if_dfs_configure
__ol_ath_attach: init tx/rx TODO
__ol_ath_attach: hard_header_len reservation 58
Initializing Pktlogs for 11ac
ath_ioctl: SIOC80211IFCREATE CALLED
wmi_unified_vdev_create_send: ID = 0 VAP Addr = 00:02:61:ba:50:85:
Getting Nss: 3
ieee80211_dfs_override_cac_timeout: CAC timeout is now overridden (2)
watchdog: disabled
Trying to start watchdog with timeout 10 seconds
ifx_ppa_init - init succeeded
[4294707376] mtlk0(_mtlk_df_user_ppa_register:616): PPA device function is registered (id=3)
device eth0 entered promiscuous mode
device wlan0 entered promiscuous mode
isCountryCodeValid: EEPROM regdomain 0x0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
Add VHT80 channel: 5210
Add VHT80 channel: 5290
Add VHT80 channel: 5530
Add VHT80 channel: 5610
Skipping VHT80 channel 5660
Skipping VHT80 channel 5680
Skipping VHT80 channel 5700
OL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
OL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
Too long sleep: 5 vs 2
ath_ioctl: SIOC80211IFCREATE CALLED
wmi_unified_vdev_create_send: ID = 0 VAP Addr = 00:02:61:ba:50:85:
Mem: 47220K used, 61844K free, 0K shrd, 5656K buff, 19784K cached
CPU:  45% usr  54% sys   0% nic   0% idle   0% io   0% irq   0% sirq
Load average: 1.52 0.35 0.11 5/51 2086
  PID  PPID USER     STAT   VSZ %VSZ %CPU COMMAND
  684   531 root     R    12416  11%  36% crm -t -f /var/log/crm.log
 2072  2071 root     R <   1856   2%   9% top -b -n 1
 1803   684 root     S     8032   7%   0% drvhlpr -p /tmp/drvhlpr0.conf -e 2
 2032   684 root     S <   3600   3%   0% watchdog --crm-timeout 180 --wdt-timeout 10
 1391  1386 root     S     1864   2%   0% {crm-hotplug} /bin/sh /usr/bin/crm-hotplug usb
 1436  1431 root     S     1864   2%   0% {crm-hotplug} /bin/sh /usr/bin/crm-hotplug usb
 1286   684 root     S     1860   2%   0% /bin/sh --login
    1    OL vap_stop +
 wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
0 root     S     1856   2%   0% init
  531     1 root     S     1856   2%   0% {crm-keeper} /bin/sh /usr/bin/crm-keeper
 1226     OL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
1 root     S     1856   2%   0% syslogd -O /var/log/crm.log -s 200
 1386     6 root     S     1856   2%   0% {crm-hotplug} /bin/sh /usr/bin/crm-hotplug usb
 2071  2032 root     S <   1856   2%   0% /bin/sh -c top -b -n 1
 1431     6 root     S     1856   2%   0% {crm-hotplug} /bin/sh /usr/bin/crm-hotplug usb
 2081     6 root     S     1856   2%   0% {crm-hotplug} /bin/sh /usr/bin/crm-hotplug net
 1224     1 root     S     1848   2%   0% klogd
 1404  1391 root     S     1552   1%   0% caction -u hotplug.usb /usb/host/updPPA REG DONE, if_id=4, dev_if_index = 12, os_unit=0 
ate_led
 1449  1436 root     S     1552   1%   0% caction -u hotplug.usb /usb/host/update_led
 1437  1431 root     S     1548   1%   0% clog -l ERROR
 1392  1386 root     S     1548   1%   0% clog -l ERROR
 2042   684 nobody   S     1444   1%   0% dnsmasq -i * -a 0.0.0.0 --keep-in-foreground -u nobody --cache=2048 -H /etc/dnrd/master --stop-dns-rebind --rebind-localhost-ok --conf-file=/tmp/dnsmasq.1_domains.conf --bind-loopback
 2086  2081 root     R        8   0%   0% [which]
  217     2 root     SW       0   0%   0% [mtdblockd]
    5     2 root     SW       0   0%   0% [events/0]
 1device wlan2 entered promiscuous mode
790     2 root     DW       0   0%   0% [mtlk]
    6     2 root     SW       0   0%   0% [khelper]
  242     2 root     SW       0   0%   0% [ubi_bgt0d]
  118     2 root     SW       0   0%   0% [kblockd/0]
  157     2 root     SW       0   0%   0% [aio/0]
  158     2 root     SW       0   0%   0% [crypto/0]
  156     2 root     SW       0   0%   0% [kswapd0]
 1425     2 root     SW       0   0%   0% [ifxhcd_workqueu]
  165     2 root     SW       0   0%   0% [crypto]
  166     2 root     SW       0   0%   0% [crypto_ret]
 1385     2 root     SW       0   0%   0% [ifxhcd_killurbd]
  116     2 root     SW       0   0%   0% [bdi-default]
 1285     2 root     SW       0   0%   0% [ipolldevd]
  127     2 root     SW       0   0%   0% [khubd]
  114     2 root     SW       0   0%   0% [sync_supers]
 1812     2 root     DW       0   0%   0% [mtlk]
 1823     2 root     DW       0   0%   0% [mtlk]
 1834     2 root     RW       0   0%   0% [mtlk]
 1384     2 root     SW       0   0%   0% [ifxhcd_workqueu]
    3     2 root     SW       0   0%   0% [ksoftirqd/0]
    4     2 root     SW       0   0%   0% [watchdog/0]
 1430     2 root     SW       0   0%   0% [ifxhcd_killurbd]
    2     0 root     SW       0   0%   0% [kthreadd]
    9     2 root     SW       0   0%   0% [async/mgr]

Configuration fil ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 
OL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
e: /tmp/hostapd-wlan2.conf
 DEVICE IS DOWN ifname=wlan2
 DEVICE IS DOWN ifname=wlan2
Using interface wlan2 with hwaddr 00:02:61:ba:50:85 and ssid "Tilgin-ZgAzu9nyYsAF_5GHz"
 
 DES SSID SET=Tilgin-ZgAzu9nyYsAF_5GHz 
WPS: ConvOL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
erting push_button to virtual_push_button for WPS 2.0 compliance
FWLOG: [44300] WAL_DBGID_SECURITY_ENCR_EN (  )
FWLOG: [44300] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
ol_ath_wmm_update:
Notification to UMAC VAP layer
FWLOG: [44440] WHAL_ERROR_RESET_CHANNF1 (  )
Tunnel link is UP
wmi_unified_vdev_stop_send 
STOPPED EVENT for vap 0 
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
Notification to UMAC VAP layer
wmi_unified_vdev_stop_send 
STOPPED EVENT for vap 0 
FWLOG: [46128] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
OL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
Configuration file: /tmp/hostapd-wlan2.conf
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
ol_ath_wmm_update:
Notification to UMAC VAP layer
 ieee80211_ioctl_siwmode: imr.ifm_active=643, new mode=3, valid=1 
wmi_unified_vdev_stop_send 
STOPPED EVENT for vap 0 
 DEVICE IS DOWN ifname=wlan2
 DEVICE IS DOWN ifname=wlan2
Using interface wlan2 with hwaddr 00:02:61:ba:50:85 and ssid "Tilgin-ZgAzu9nyYsAF_5GHz"
CRM state '/voip/call/table' flags=0 saving...
CRM state '/voip/call/table' flags=0 saving... done. Status=EOK Count=0
CRM state '/' flags=0 saving...
WPS: Converting push_button to virtual_push_button for WPS 2.0 compliance
OL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
ol_ath_wmm_update:
Notification to UMAC VAP layer
CRM state '/' flags=0 saving... done. Status=EOK Count=1185
find: /sys/class/scsi_disk/*/uevent: No such file or directory
FWLOG: [47481] WAL_DBGID_SECURITY_ENCR_EN (  )
FWLOG: [47481] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
find: /sys/class/tty/tty????/uevent: No such file or directory
find: /sys/class/tty/wwan?/uevent: No such file or directory
find: /sys/class/usb/lp*/device/uevent: No such file or directory
1970-01-01 00:00:51: (/space/sources/02_07/factory/src/vood/ng/02_07/lighttpd/src/log.c.164) server started 
wmi_unified_vdev_stop_send 
STOPPED EVENT for vap 0 
OL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
Tx power value is greater than supported max tx power 63, Limiting to default Max
Getting VHT MCS MAP set: 0
Configuration file: /tmp/hostapd-wlan0.conf
Using interface wlan0 with hwaddr 00:02:61:ba:50:82 and ssid "Tilgin-ZgAzu9nyYsAF"
udhcpd (v1.21.1) started
WPS: Converting push_button to virtual_push_button fo[4294721036] mtlk0(_mtlk_core_mbss_is_rescan_exempted:2758): Re-Scan cannot be exempted (20/40 is active)
[4294721046] mtlk0(mtlk_mbss_init:3439): CID-0000: _mtlk_core_mbss_check_activation_params returned successfully
[4294721056] mtlk0(_mtlk_mbss_preactivate:2917): CID-0000: Pre-activation configured parameters:
[4294721066] mtlk0(mtlk_core_configuration_dump:4938): CID-0000: Country             : SE
[4294721076] mtlk0(mtlk_core_configuration_dump:4939): CID-0000: Domain              : 48
[4294721086] mtlk0(mtlk_core_configuration_dump:4940): CID-0000: Network mode        : 802.11bgn
[4294721086] mtlk0(mtlk_core_configuration_dump:4941): CID-0000: Band                : 2.4
[4294721096] mtlk0(mtlk_core_configuration_dump:4942): CID-0000: Prog Model Spectrum : 40 MHz
[4294721106] mtlk0(mtlk_core_configuration_dump:4943): CID-0000: Selected Spectrum   : 40 MHz
[4294721116] mtlk0(mtlk_core_configuration_dump:4944): CID-0000: User Sel. Spectrum  : 40 MHz
[4294721126] mtlk0(mtlk_core_configuration_dump:4945): CID-0000: Bonding             : lower
[4294721126] mtlk0(mtlk_core_configuration_dump:4946): CID-0000: HT mode             : enabled
[4294721136] mtlk0(mtlk_core_configuration_dump:4948): CID-0000: SM enabled          : enabled
[4294721146] mtlk0(mtlk_aocs_set_config_frequency_band:3162): Overriding AOCS type for 2.4 GHz (NONE)
[4294721156] mtlk0(_mtlk_mbss_preactivate:2932): CID-0000: Start AOCS
[4294721166] mtlk0(_mtlk_mbss_preactivate:2945): CID-0000: ap_scan_band_cfg = 1
[4294721166] mtlk0(_mtlk_core_perform_initial_scan:2701): CID-0000: Scan started 40MHz
[4294721176] mtlk0(do_scan:596): Starting normal scan...
mtlk mtlk.0: firmware: requesting ProgModel_BG_CB_ar10.bin
r WPS 2.0 compliance
mtlk mtlk.0: firmware: requesting ProgModel_BG_CB_40_RevI_ar10.bin
[4294721666] mtlk0(prepare_progmodel_string:2061): CID-0000: ProgModel: ProgModel_BG_CB_40_RevI_ar10.bin version 2025

[4294723606] mtlk0(_mtlk_core_perform_initial_scan:2701): CID-0000: Scan started 20MHz
[4294723606] mtlk0(do_scan:596): Starting normal scan...
mtlk mtlk.0: firmware: requesting ProgModel_BG_nCB_ar10.bin
mtlk mtlk.0: firmware: requesting ProgModel_BG_nCB_40_RevI_ar10.bin
[4294723816] mtlk0(prepare_progmodel_string:2061): CID-0000: ProgModel: ProgModel_BG_nCB_40_RevI_ar10.bin version 2025

OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
ol_ath_wmm_update:
ol_if_dfs_configure: called
ol_if_dfs_configure: ETSI domain
ol_if_dfs_disable: called
ol_if_dfs_enable: called
cac_start chan 5500 timeout 2 sec, curr time: 4294726 sec
Notification to UMAC VAP layer
[4294726736] mtlk<3>(_aocs_is_non_wifi_noise:3612): Force to 20 MHz mode due to interferer detection: RSSI:-43 thrsh:-60
[4294726736] mtlk<4>(aocs_detect_non_wifi_noise:3638): Coexistance switching to 20MHz Mode
[4294726746] mtlk0(_mtlk_core_aocs_on_spectrum_change:2879): CID-0000: Spectrum changed to 20MHz
[4294726756] mtlk0(_mtlk_mbss_preactivate:3040): CID-0000: Pre-activation selected parameters:
[4294726766] mtlk0(mtlk_core_configuration_dump:4938): CID-0000: Country             : SE
[4294726776] mtlk0(mtlk_core_configuration_dump:4939): CID-0000: Domain              : 48
[4294726786] mtlk0(mtlk_core_configuration_dump:4940): CID-0000: Network mode        : 802.11bgn
[4294726786] mtlk0(mtlk_core_configuration_dump:4941): CID-0000: Band                : 2.4
[4294726796] mtlk0(mtlk_core_configuration_dump:4942): CID-0000: Prog Model Spectrum : 20 MHz
[4294726806] mtlk0(mtlk_core_configuration_dump:4943): CID-0000: Selected Spectrum   : 20 MHz
[4294726816] mtlk0(mtlk_core_configuration_dump:4944): CID-0000: User Sel. Spectrum  : 40 MHz
[4294726826] mtlk0(mtlk_core_configuration_dump:4945): CID-0000: Bonding             : lower
[4294726826] mtlk0(mtlk_core_configuration_dump:4946): CID-0000: HT mode             : enabled
[4294726836] mtlk0(mtlk_core_configuration_dump:4948): CID-0000: SM enabled          : enabled
[4294726846] mtlk0(_mtlk_channels_frequency_element_dump:3086): CID-0000: Channel        : 1
[4294726856] mtlk0(_mtlk_channels_frequency_element_dump:3087): CID-0000: ChannelACT     : 0
[4294726866] mtlk0(_mtlk_channels_frequency_element_dump:3088): CID-0000: ScanType       : 0
[4294726876] mtlk0(_mtlk_channels_frequency_element_dump:3089): CID-0000: ChannelSwCnt   : 0
[4294726886] mtlk0(_mtlk_channels_frequency_element_dump:3090): CID-0000: SwitchMode     : 0
[4294726886] mtlk0(_mtlk_channels_frequency_element_dump:3091): CID-0000: SmRequired     : 0
[4294726896] mtlk0(_mtlk_channels_frequency_element_dump:3092): CID-0000: CbTxPowerLim   : 116
[4294726906] mtlk0(_mtlk_channels_frequency_element_dump:3093): CID-0000: nCbTxPowerLim  : 116
[4294726916] mtlk0(_mtlk_channels_frequency_element_dump:3094): CID-0000: AntennaGain    : 0
[4294726926] mtlk0(_mtlk_channels_frequency_element_dump:3095): CID-0000: ChannelLoad    : 0
[4294726936] mtlk0(_mtlk_channels_frequency_element_dump:3097): CID-0000: MaxTxPwr[0]    : 0
[4294726936] mtlk0(_mtlk_channels_frequency_element_dump:3098): CID-0000: MaxTxPwrIdx[0] : 0
[4294726946] mtlk0(_mtlk_channels_frequency_element_dump:3097): CID-0000: MaxTxPwr[1]    : 0
[4294726956] mtlk0(_mtlk_channels_frequency_element_dump:3098): CID-0000: MaxTxPwrIdx[1] : 0
[4294726966] mtlk0(_mtlk_channels_frequency_element_dump:3097): CID-0000: MaxTxPwr[2]    : 0
[4294726976] mtlk0(_mtlk_channels_frequency_element_dump:3098): CID-0000: MaxTxPwrIdx[2] : 0
[4294726976] mtlk0(_mtlk_channels_frequency_element_dump:3100): CID-0000: SwitchType     : 0
[4294726986] mtlk0(_mtlk_mbss_send_preactivate_req:2829): CID-0000: Sending UMI FW Preactivation
[4294727066] mtlk<3>(mtlk_core_set_force_ncb:6653): CID-0000: Error returned for UMI_FORCE_NCB request to MAC (err=2)
[4294727076] mtlk0(_mtlk_mbss_preactivate:3070): CID-0000: _mtlk_mbss_preactivate returned successfully
[4294727086] mtlk0(mtlk_mbss_init:3446): CID-0000: _mtlk_mbss_preactivate_if_needed returned successfully
[4294727086] mtlk0(mtlk_mbss_send_vap_activate:3134): CID-0000: Entering mtlk_mbss_send_vap_activate
[4294727096] mtlk0(mtlk_mbss_send_vap_activate:3141): CID-0000: Start activation
[4294727106] mtlk0(__mtlk_dump:66): dump of UMI_ACTIVATE_VAP:
cp= 0x86220700 l=152
0000:  00 02 61 ba 50 82 00 00  02 00 00 05 00 0f 00 00 
0010:  aa 0f 00 00 55 00 00 00  ff ff ff ff 13 00 00 00 
0020:  54 69 6c 67 69 6e 2d 5a  67 41 7a 75 39 6e 79 59 
0030:  73 41 46 00 00 00 00 00  00 00 00 00 00 00 00 00 
0040:  00 00 00 00 30 18 01 00  00 0f ac 02 02 00 00 0f 
0050:  ac 04 00 0f ac 02 01 00  00 0f ac 02 00 00 00 00 
0060:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
0070:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
0080:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
0090:  00 00 00 00 09 00 00 00  
[4294727166] mtlk0(mtlk_mbss_send_vap_activate:3203): CID-0000: UMI_ACTIVATE_VAP
[4294727166] mtlk0(mtlk_mbss_send_vap_activate:3204): CID-0000:   sBSSID = 00:02:61:BA:50:82
[4294727176] mtlk0(mtlk_mbss_send_vap_activate:3205): CID-0000:   sSSID = Tilgin-ZgAzu9nyYsAF
[4294727186] mtlk0(mtlk_mbss_send_vap_activate:3206): CID-0000:   Hidden = 0
[4294727196] mtlk0(__mtlk_dump:66):   sRSNie = 
cp= 0x86220744 l=80
0000:  30 18 01 00 00 0f ac 02  02 00 00 0f ac 04 00 0f 
0010:  ac 02 01 00 00 0f ac 02  00 00 00 00 00 00 00 00 
0020:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
0030:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
0040:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
[4294727226] mtlk0(mtlk_mbss_send_vap_activate:3210): CID-0000: mtlk_txmm_msg_send, MsgId = 0x453, ESSID = Tilgin-ZgAzu9nyYsAF
[4294727246] mtlk0(mtlk_mbss_init:3453): CID-0000: mtlk_mbss_send_vap_activate returned successfully
wmi_unified_vdev_stop_send 
STOPPED EVENT for vap 0 
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
ol_if_dfs_configure: called
ol_if_dfs_configure: ETSI domain
ol_if_dfs_disable: called
ol_if_dfs_enable: called
cac_start chan 5500 timeout 2 sec, curr time: 4294727 sec
Notification to UMAC VAP layer
cac_timeout cac expired, chan 5500 curr time 4294729
TAPI, Version 4.10.4.2, (c) 2001-2013 Lantiq Deutschland GmbH
Lantiq MIPS34KEc MPS driver, version 2.2.7.0, (c) 2006-2010 Lantiq Deutschland GmbH
Lantiq VMMC device driver, version 1.15.0.4, (c) 2006-2013 Lantiq Deutschland GmbH
bkos: hal received command 2
CRM is considered alive and well - removing threat limit